2018 April New Cisco 300-180 Exam Dumps with PDF and VCE Free Updated Today! Following are some new CV0-001 Real Exam Questions:
1.|2018 Latest 300-180 Exam Dumps (PDF & VCE) 374Q&As Dowenload:
2.|2018 Latest 300-180 Exam Questions & Answers Download:
A customer is troubleshooting the CIMC and resets the CIMC.
Which three settings are defaults for the CIMC after it is reset? (Choose three.)
A. SSH and Telnet are disabled from accessing the CIMC CLI.
B. HTTPS enabled for accessing the CIMC GUI.
C. A user account named admin exists that has a password of password.
D. DHCP is disabled on the management port.
E. The boot order is EFI, CDROM, PXE (using LoM), FDD, and HDD.
F. KVM and vMedia are disabled.
G. USB is disabled.
Which two options are ways to identify the exact BIOS version of a Cisco UCS C-Series Rack-Mount Server? (Choose two.)
A. Use the iFlash32 command and select the -i option.
B. Press F2 during server bootup.
C. Press F6 during server bootup.
D. Press F12 during server bootup.
E. Press F10 during server bootup.
F. Use the EFI interface.
Which statement about when the FSM on a blade is set to FsmComputeBladeDiscoverCimcInventory is true?
A. The Object is a ComputeBlade, the Workflow being performed is Discover, and the current Operation is CimcInventory on the managingInst node.
B. The Object is a Compute, the Workflow being performed is BladeDiscover, and the current Operation is CimcInventory on the managementInst node.
C. The Object is a ComputeBlade, the Workflow being performed is Discover, and the current Operation is CimcInventory on the master node.
D. The Object is a Compute, the Workflow being performed is BladeDiscover, and the current Operation is CimcInventory on the master node.
Which command must you use to find information about system event logs?
A. UCS-TEST-DMZ-A/security #show audit-logs
B. UCS-TEST-DMZ-A/cimc/log#show entries
C. UCS-TEST-DMZ-A/system/control-ep#show communication-policy-ctrl
D. UCS-TEST-DMZ-A#/org/service-profile#show pending-changes detail
Which two commands check for DIMM errors in a Cisco UCS environment? (Choose two.)
A. UCS-TEST/chassis#show error-recovery
B. UCS-TEST/chassis/server/memory-array#show stats
C. UCS-TEST/chassis/server#show execute-disable
D. UCS-TEST/chassis/server/memory-array #show block
E. UCS-TEST/chassis/server#show memory-array detail
F. UCS-TEST/chassis/server#show error-recovery
Some of your servers do not have IP connectivity to the upstream network. Which two commands do you use to identify whether a data path is up and running on a switch? (Choose two.)
A. show platform fwm info hw-stm
B. show interface brief
C. show npvflogi-table
D. show mac-address table
E. show pinning border-interfaces active
You have blade servers that run VMware ESXi. Which two tasks do you perform to ensure that all of the components in the Cisco UCS environment use jumbo frames? (Choose two.)
A. Use a QoS policy for the jumbo frames.
B. Configure the MTU on the vSwitch.
C. Configure the fabric interconnect to support 9500-byte frames.
D. Configure the MTU on the vNIC.
E. Configure a QoS policy on the vSwitch.
After a Cisco UCS Manager upgrade, you discover issues relating to the IQN of several service profiles. Which two options are possible causes of the problem? (Choose two.)
A. duplicate service profiles
B. a duplicate IQN within a service profile
C. a duplicate IQN across multiple service profiles
D. an unsuccessful upgrade
E. incorrect VSAN settings
You have a Cisco UCS cluster and you must recover a lost admin password. In which order must you power cycle the fabric interconnects?
A. primary first, and then secondary
B. secondary first, and then primary
C. primary and secondary simultaneously
D. primary only
After you hot swap an HDD, the updated HDD metrics fail to appear in the Cisco UCS Manager GUI. Which option is the most likely cause of the problem?
A. The Cisco UCS Manager gathers hard disk metrics only during a system boot.
B. The hard disk firmware version is unsupported.
C. The hard disk failed to initialize.
D. The hard disk is a member of a RAID-1 array.
You have a Cisco UCS Fabric Interconnect in Fibre Channel end-host mode.
You must check whether all of the Fibre Channel targets are available through the fabric interconnect at VSAN 200. Which command must you use?
A. show npvflogi-table
B. show flogi-table
C. show flogi database
D. show zoneset active VSAN 200
|One Time Purchase||✔||✖||✖||✖||✖|
|100% Pass Guarantee||✔||✖||✖||✖||✖|
|100% Money Back||✔||✖||✖||✖||✖|